The channel send knobs and bus assign switches make it easy to send the signal from each channel to the stereo, group, internal effect, and auxiliary buses as required.
All input channels have a total of six auxiliary sends: AUX send 1 through 4 can be switched for pre- or post-fader operation, while AUX sends 5 and 6 are post-fader. That's more than sufficient send capability to handle monitoring and effects for all but the most complex applications. Two stereo AUX returns are provided in addition to the internal effect returns, providing an extra margin of return versatility for wet monitoring, for example.
Independent phone-jack outputs are also provided for group buses 1 through 4. The main stereo outputs and mono output feature rugged, reliable XLR type connectors.
Not only do these connectors lock to minimize the chance of accidental disconnection, but they provide superior electrical contact for long-term dependability as well. A low-pass filter with a roll-off frequency that can be varied from 80 to Hz is provided on the mono output for convenient connection and optimum matching with a subwoofer. Four high-visibility segment meters are switchable to allow precise visual monitoring of levels on the main stereo bus, the four group buses, the stereo 2-track input, the PFL Pre-Fader Listen bus, or the AFL After-Fader Listen bus.
Effect programs include reverb, delay, pitch change chorus, phaser, voice doubler, and distortion. The effects include editable parameters so they can be customized as required, and processor "B" even has a TAP switch for real-time tap-tempo entry. With these top-performance effect processors built in, you wont have to transport and set up racks of external effects to create your sound. The channel ON switches, PFL Pre-Fader Listen switches and phantom power switches are original Yamaha illuminated types, so it's easy to visually check vital console settings.
A talkback microphone input is provided for easy, efficient communication between the sound engineer and musicians and staff in live-sound applications, during setup, rehearsal, and the actual performance. The design of the faders, rotary controls and switches used on the MG mixers, as well as the way they are laid out, allow easy operation and visual confirmation of settings. Overview Features Gallery Specs Downloads. Professional Audio Toggle navigation. Seite The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product.
A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
These precautions include, but are not limited to, the following:. The required voltage is printed on the name plate of the device.
The device contains no user-serviceable parts. Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property.
Pulling by the cord can damage it. Otherwise, the device, TV, or radio may generate noise. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. Vent holes are located on the top, bottom, front, rear, and sides of this machine. All vent holes must remain unblocked to prevent overheating. Before turning the power on or off for all devices, set all volume levels to minimum.
If this happens, turn off the power immediately and unplug the power cord from the AC outlet. If you experience any hearing loss or ringing in the ears, consult a physician.
Insert TRS phone jacks are wired as follows: sleeve: ground, tip: send, and ring: return. The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of the product during operation.
NOTE: This product has been tested and found to comply with. The wires in this mains lead are coloured in accordance with the following code:. As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying the terminals in your.
This console offers excellent cost-performance and is ideal for use as the main mixer in an SR setup or as part of an installed system. Be sure to retain this manual in a safe place. Also provides four line-level stereo inputs. These switches make it easy to selectively monitor the input and output signals through headphones connected to the PHONES jack. The phantom power can be independently switched on and off in eight-channel blocks.
These jacks can also serve as an auxiliary stereo input. Be sure to unplug the power cord from the outlet if you are not going to use the mixer again for an extended period, and whenever there are lightning storms in the area.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Supplies 12V to Pins 2 and 3. Pin 1 is not connected. Liefert 12 V an Pins 2 und 3. Pin 1 ist nicht verbunden. Fournit une tension de 12 V aux broches 2 et 3. The above warning is located on the rear of the unit.
CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property.
0コメント